Monthly Archives: March 2013

Makerbot Replicator 2x Journal Entry 2

Share this:  

Well, yesterday was a busy day for me just immersing myself in the world of 3D printing. I want to keep this post short so I have more time to actually do more 3D printer stuff and maybe kick back on my remaining day off from work!

Let’s see:

  • I called Makerbot about my heater error.
  • They emailed me instructions for checking the thermocouple connections to the circuit board inside the printer.
  • I followed the instructions (I want to do a detailed post on this later).
  • It seemed to work… for a while…
  • I printed a 2nd Mr. Jaws for my nephews in Red ABS plastic. It printed nicely.
  • A little later the error message popped up again. Grrrrr!
  • I called Makerbot Support again and told them my woe.
  • They are sending me a new thermocouple cable free of charge. It will take a few days to get here (for fast shipping I would have to had to pay).
  • The thermocouple that is acting bad is for the right extruder.
  • In the mean time, I have not actually used the left extruder yet so I decided to start messing around with that!
  • While I had tech support on the phone I had a mess of questions I wanted answered in my notebook. I asked those questions (and two or three more) and built up my knowledge base quite a bit! There is still so much to learn! BTW, I did not feel rushed by the support person (I felt more rushed by myself)!
  • I hope to write other posts regarding the information I found out about on that call.
  • I picked another object out on Thingiverse to print in Natural ABS plastic (white). Its called Melting Ball in a Cage (thing:62856).
  • If you look at a picture of this thing it probably should have been called Ball in a Melting Cage!
  • It was printed in white PLA. I have white ABS. How hard could this be?
  • Even after leveling the build platform carefully I am having a hard time:
    • Even printing the raft.
    • Getting the plastic to consistently come out of the extruder!
  • The white ABS seems a bit runny.
  • The first thing I want to do today is try the print again with a lower temp on the extruder and see if that helps.

Wish me luck!

Makerbot Replicator 2x Journal Entry 1

Share this:  

First off, I decided to keep a paper journal just for my printer. Working with this 3D printer is more than a notion! I’ve run into various problems, learned various things, there’s a lot to keep track of! I want to put in this electronic version of a “journal” on my blog here to share what I have learned. This is the first entry. I plan on recording stuff based on reviewing my paper journal as well as trying to recall other things that I did not write down. Hopefully in the process, I will build up my body of knowledge and help others who read my blog posts on this subject. some things in this post may be slightly out of order.

I did not have a paper journal at first. So some of the details may be missing. I am going to get better at this! I don’t want my 3D printer to just end up being a very expensive paper-weight!

Comb
I mentioned in a previous post that I printed a comb from the SD card that came with the printer. I printed the comb in a translucent (Icicle Blue) PLA plastic filament. What next?

iPhone Case
I downloaded an iPhone case of the Thingiverse site. I was not keeping track of “thing” ids at this point. This print was like day 2 of me having the printer. I started printing it in Icicle Blue PLA plastic. After doing a good deal of the case back, the extruder started clicking and the plastic was not coming out of it. I paused the printer and swapped in red ABS filament!  So I was impatient! The print finished but was a bit de-laminated. Not to mention it was a bit too small to fit on my iPhone 4.

Switching from PLA to ABS… Why?
I did this because I read on some sites that PLA has more of a tendency to not feed into the extruder properly after the extruder has been running hot for awhile… so I switched to ABS.  Maybe not the best idea, but I think its a learning experience.

HeartSpring (thing:51979)
I decided to attempt to print this because my wife liked it. I probably was picking something too complex for me at this point. I will comment more about using the Makerware software later in another post. I was having a bear of a time getting the print to stick (even just printing a raft let alone printing the actual heart)! I learned about Kapton tape and installed a piece that came with the printer. I finally got somewhere here, but the print started really messing up about 21mm  high… it was so bad I canceled the print. I was using supports (which actually may have been a mistake in this case).

On my half-way decent start I had added blue painter’s tape to the build plate (I made it 2 sided). I found out later that the painter’s tape is more to be used printing in PLA. I was printing in Red ABS. I probably would have had better luck if  I had leveled the build platform better.

Tech Support
I called tech support in the afternoon… I had to leave a voice message. My message was basically about my problems getting even my raft to stick to the build platform. About 3 days later I got a call. It seemed my problem most likely had more to do with more precisely leveling the build platform. I would have liked to have talked with them longer but I had a call for my job I needed to get on. I gotta call back!

Printer Cover
At this point I did not have the cover for my printer… so I made one from a inexpensive plastic storage container that I bought at Target. I bought other plastic storage containers to store all my 3D printing stuff too! I used my improvised printer cover during my last attempt at the heartspring object.

I called Makerbot about my printer cover because it was listed on the packing slip but was not included in any box that I received. The web site seemed to indicate everything had shipped. Anyway, I found out from the folks at Makerbot that it had not shipped. A couple days later I received my new cover along with an extra spool of filament. Thanks for the spool Makerbot!

Bracelet
My wife saw a bracelet  on Thingiverse that she liked (sadly I do not know the thing id), I downloaded the file and tried to print. The render took forever and I saw some things about the model that made me worry so I cancelled the print. I downloaded another bracelet model (again, I did not record the thing id). I spent some extra time leveling the build platform and the print (in red ABS) started really well! This is the first time in ABS that my raft stuck to the build plate without any problems. And the printing of the bracelet itself started very well. Alas, when the bracelet was about 5mm high it started to”come off the rails.” At the suggestion of my wife I let the print finish just to see what we would get. As you can see in the photo, its not something wearable!

E-Gads! Heater Error!
Whilst I was looking over my scruffy bracelet print my printer got an error: Heater Error! My temperature reads are failing! Please Chek my connections. Yikes. I found somewhere info about making sure the wires into the extruder were pushed in properly, they seemed to be. 🙁

I turned the printer off and waited awhile… then turned it back on. The error went away… for awhile.

Mr. Jaws
My two nephews dropped by and I printed a Mr. Jaws from the SD card. I printed it in red ABS. After an initial problem, this printed perfectly. My nephews were fighting over Mr. Jaws! I need to print another one so they each have one.  My wife and I went to dinner and I left the printer on to cool down. When we got back the heater error was back. 🙁

Now, even when I turn the printer off for a long period of time, and then turn the printer back on I get the error right away. It is happening for the right extruder. Grrrrrr!

The 3D printer saga continues…

What You Can Do with Web Apps in HTML5: A Response

Share this:  

Hello all, I felt the need to respond to a discussion that was had on Web Apps and HTML5 on the tech show “The Gillmor Gang”… the “Pinch and Spread” episode. What was said was interesting but it seemed to be that the gang was coming to conclusions based on too limited a view of what HTML  5 was capable of. The embedded video I hope explains it all more fully. Hopefully you can pardon my excessive use of vocal pauses (umm), and you will still get a good grounding of the potential that HTML 5 has and what it can to do for the mobile space.

Link to discussion on programmatically determining if the browser is running on a regular iPad or an iPad Mini:   Detecting iPad Mini in HTML5
How to Detect iPad Mini Using Javascript
Note regarding the two links above: After looking into this deeper it seems that the difference in the values for availableWidth and availableHeight are due to the different tab counts when testing this code. So this is probably not very useful after all. 🙁

Amazon link to book:   Building iPhone Apps with HTML, CSS, and JavaScript by Jonathan Stark. Note that I bought this also as an eBook on Apple’s iBooks and some of the page formatting in the reader there is really screwed up.

Related Chomer.com Posts:
Programmatically Determining if in Full Screen Mode in Mobile Safari